Recenzje klientów dla Frezarka CNC VEVOR, wrzeciono 500 W, 3-osiowa maszyna grawerująca, obszar roboczy 300x180x80 mm, sterowanie offline, wyłączniki krańcowe, zatrzymanie awaryjne, do rzeźbienia i cięcia drewna, akrylu i plastiku.

The assembly directions are poor even more so the electrical. The overall build is good and function well after you figure it all out. Also figuring out what software will drive the unit is a bit of a challenge too. Maybe it's all because I am new to the CNC world, but it's supposed to be a beginner machine.

Wasn’t too bad to assemble, there’s decent instructions for that part. The software / running of the machine lacks though. Also didn’t help that the x axis belt was wayyyy too tight and caused the motor to bind up. Took about a hour of deep diving to figure that out on my own and get it working. Customer service isn’t the best either with limited technical support.

Can’t get it to do anything can’t seem to get a program to make it run

It’s ok

I purchased this CNC assuming based on what i read it would be simple to set up and run.That was not the case . The build / assy of the CNC was relatively simple however the SW ( software ) to utilize the machine did not work in fact tthere was nothing on the USB provided . As many of us doing wood working we do not have the latest and greatest equipment and so when i tried to set up the CNC with my older MAC it did not work , we had to go in several and i mean several options to find out how we could down load the SW which took 4 to 5 hours ( yes 4 to 5 hrs) . once the SW was installed i was able to move the arm in all directions. however now i want to use it and it did not come with information for the first time users and hence that is where i am stalled out , going onto youtube to find out how to use machine. for anyone wanting to buy a CNC and not a programmer or never used one before do you self a favor and do research and learn how and what to do before you get this or any machine . So i am not sure how it works to run anything at this point so hard to advise on its ability. Good luck to any and all hope you have better luck than i did .

Very bad costumer service , they keep closing the tickets to avoid return and refund , the machine has a seriouse issue with the Z axis and X axis , wrote to them 3 times and they kept maneuvering, not worth the money , it is a total time waste !

I bought this and it was shipped and receive quickly. Packaging was nice and protected the engraver well. The problems with it came with assembly. First the bolt holes on the Z axis side places were off so I couldn't get the screws in. I fixed that by opening up the holes. Then when installing the wiring 2 of the connectors wouldn't reach the plugs. Both the Z and X axis wires were installed in the harness with too little slack in them. I had to take the plastic spiral wrap off and pull more wire out so I count connect the wires to the servo motors. Then there is a wire cover part #22 missing from the box. Contacting customer support got a reply with a bunch of silly requests so I will fix that on my own also. I haven't even gotten it running yet and I am unhappy with the purchase.

I haven't been able to get it running yet. It's not a simple as the laser engravers. The screws to assemble the frame are too short, they only thread into the nuts a couple of threads. I replaced them with longer ones so it won't fall apart. Out of the 6 holes to mount the spindle, only 4 of them were tapped, I had to buy a tap to complete the job. Overall low quality / poor quality control.

Way too had to get a good code file to use in Candle. Have not been able to do one proper engraving

The customer service is subpar all it takes forever to get replies. The product pamphlet does not give all the information about how the hook it up. My machine was missing part and falty parts ,been working with them for about two weeks still haven't got to use this machine yet. Paid close to $800 for a worthless machine. I bought a lot of products from this company but I will not buy no more.