Recenzje klientów dla VEVOR Ręczna gilotyna do papieru (do formatu A3, pojemność 400 arkuszy), gilotyna do papieru z dźwignią, nożyce gilotynowe do papieru o najwyższej precyzji, biuro, dom, szkoła

Very bad product. Absolutely impossible to adjust. Although after a few hours I managed to adjust the knife so that it cuts all the way, the whole mechanism bends the edges of the paper and even if it is fine, the press is unable to hold the stack, so the top part completely shifts and crumples. I tried to devote several days to it and somehow adjust it, but the mechanics are poorly thought out and cannot be used. I ask for a refund. I am very sorry, the product is otherwise solidly made. too bad

Ik hoop dat het alleen mijn snijder is. Maar het lukt me niet om elke keer een stapeltje van 4 tot 10 mm A3 goed te snijden. Elke keer moet ik weer de stelschroeven afstellen. Verder hoe strak ik ook de aandruk plaat vast zet op het papier het blijft richting de zij liniaal schuiven met als gevolg dat ik vrijwel altijd een vervelende duw vouw in het papier krijg. Verder is de uitvoering anders dan de afbeeldingen in de handleiding en de site!

Je ne suis pas satisfaite de cet achat. L'huile sort et salit les pages malgré le fait d'essuyer avant chaque utilisation (ce qui rajoute du temps d'utilisation). Outre cela, il ne coupe pas jusqu'au bout. Je dois finir au cutter. Le SAV n'a malheureusement pas été d'un grand secours. Et pour le rock je trouve ça vraiment dommage.

Velice nekvalitní, nedá se řezat ve vrstvě, řezaný papír je posouván nožem o přes silné utažení přídržnou lištou. Nespokojen.

I am very disappointed in this product! It has been delivered not as shown. It does not have an adjustable, locking paper bar as shown in the picture. Instead, it has a plastic angle with round magnets on one side to attached to the base of the cutter. This angle will easily move allowing paper to be cut at different unintended lengths

Product *works* out of the box, instructions were simple to follow, didnt actually need them to use. Safety mechanism failed within days, but that does not stop the tool from working. still functions as a cutter. Issues: 1. The fence that comes pre-installed on the base of the machine is not square to the cutting blade or the printed grid on the tool so cuts are never truly square, and this cant be adjusted as the fence sits in pre cut slots and the bolts are only there to lock it down. 2. The cutting stick that sits under the blade sits proud of the level of the base. so when the paper is sitting flat on the base of the machine, the edge being cut is slightly raised up. so once the cut has been made, if cutting "blocks" of paper, the cut is not vertically square as the paper has been skewed up. There are adjustment bolts that screw in underneath the rubber, but even backed all the way out/removed, it still sits proud. Overall the product is functional. If you are a hobbyist and don't need millimeter perfect angles/cuts, its perfectly adequate. But thats about as far it goes. Adequate.

I’m not completely satisfied with this knife. The cutting is not as precise as it should be, and one part of the blade doesn’t cut all the way through, which I had to adjust myself. Paper can sometimes slip under the guard (or guide), which affects the accuracy of the cut. The knife is quite solid and feels sturdy at first, giving the impression of a high-quality tool. However, for the type of work it’s intended for—where every millimeter matters—it really should be much more precise.

Virker som den skal

No se si le pillaremos el punto de cortar con la medida exacta, (pues el tope trasero no es muy fiable) ni a cortar tantas hojas como dice, pues aunque sean cincuenta hojas de papel de 80 gramos y apretando bien el pisón hay variación de arriba a bajo.

Product would be great with a few improvements. The back guide needs to be longer going to the opposite side with a clamp or similar screw down guide like opposite side. When you tighten the clamp holding a larger stack of paper in place to cut, the action of the blade pushes the back guide and you get an uneven cut. If you tighten the clamp extra tight that gives you a wrinkle in the stack. I bought some heavy duty magnets to compensate but it is inconvenient when trying to make minute adjustments. The grid doesnt allow for the 1/8" difference between the clamp and the actual blade cut so you need to adjust for this in your measurement. It is best to draw out a cut line and lower the blade somewhat to see if it matches up.