Recenzje klientów dla VEVOR Obudowa elektryczna ze stali, 40x40x20 cm, stal węglowa IP65

i had tried this product for my project and found it perfect for my need. i have completed adding my components to the first one i purchased from you. it worked so well i purchased another 11 enclosures from you.

This electrical box is an excellent buy, good, sturdy design, great price. Only negative I can see is that the lock is a bit simple with a key that looks like it's made of plastic.

Very hard to find a large heavy duty metal box like this that doesn't cost the earth. Well made, nice and square with no sharp edges and comes with weather proof door seal and gasket.

Just want to say.... I was pleasantly surprised when i open the box and saw the quality of the enclosure. The price was right, and i will be purchasing additional panels in the future. i have already recommended to several of my associates. Thank You

It is a very well made heavy-duty enclosure, I will use it as the VFD to control 3 phase condenser.

I have used a lot of these enclosures but the one thing that I do not like or understand is the large hole in the bottom. Why create an unnecessary hole in a NEMA rated enclosure? Our last batch of enclosures has an even larger hole in the bottom. We drill the holes for conduit or glands where needed. Please make a model of enclosure without any holes in it. Thank you.

Good quality easy to install. Good quality for the price. I have a 15A powerpoint wil a meter to monitor the amount of electricity I use to charge my car.

La réalisation du boîtier semble être de très bonne qualité. Le joint est ferme, ce qui laisse présager une parfaite herméticité de l'ouverture du boîtier. Il y a cependant quelques points de vigilance à retenir : - Les trous ne sont obstrués que par des capuchons en plastique blanc. Si les 4 au dos du boîtier seront obligatoirement ôtés pour le fixer à un support, et les trous comblés par la vis qui va traverser chacun d'entre eux, ainsi que l'écrou intégrant un joint caoutchouc placé à l'intérieur du boîtier, les 2 sur la face avant permettant d'inverser la position des charnières restent obstrués par ces mêmes capuchons en plastique de façon permanente, uniquement emboîtés dans le trou. Il n'assurent aucune étanchéité et l'écart entre la porte et leur emplacement est suffisamment grand pour laisser passer l'eau, même par simple ruissellement. Il faudrait utiliser ce boîtier annoncé IP65 dans un endroit protégé pour assurer l'absence d'infiltration d'eau, ce qui est plutôt illogique. - L'ouverture du bas sur laquelle se fixe la plaque à usiner, pour placer des presse-étoupes par exemple, est légèrement surélevée par rapport au bas du boîtier. J'imagine que cela permet d'éviter l'infiltration d'eau par capillarité, mais cela créé également un petit volume à l'intérieur du boîtier en bas dans lequel l'eau qui s'est infiltrée peut stagner et aboutir à un fort taux d'humidité fatal pour les équipements qu'il renferme. Un petit trou d'évacuation de cette eau est à envisager, même pour évacuer uniquement la condensation causée par la différence de température entre l'extérieur et l'intérieur du boîtier. - La plaque fournie pour fixer les éléments qui seront intégrés dans le boîtier ne permet pas de bénéficier de toute la surface disponible à l'intérieur. J'ai redécoupé une plaque alu un peu plus large qui s'insère également sans problème dans le boîtier. En résumé, je ne suis pas très confiant quand au sort de l'électronique (nœuds LoRa et Meshtastic) que je vais intégrer dans ce boîtier, qui sera fixé en pied de mat d'antenne TV, en bordure de toiture, face aux vents dominants. J'espérais obtenir quelque chose de plus durable et tout aussi efficace qu'un boîtier Plexo...

Overall I’m happy with it. I’m glad I went with the 20” height. I was going to to the 16” initially as my EA Charger is spec’d a bit below that. However I honestly doubt I would have been able to make anything less than this height work. I just needed that room to work and secure the nuts. I did have to modify it a bit. I took a circular hole drill-bit to cut a half circle into the bottom rectangular opening. I did this to get the plug and cord through. I decided this much easier than opening up my charger and disconnecting everything to pull the plugs out that way. Then I would have had to reconnect it all while in the box…. No thx. Anyways all said and done, I’m very happy with it. I love the look and everything. The only down vote I give that prevented it from getting a 5 star review is the lock that comes with this box…. The “key” is a joke. No key is really even needed. You can turn this lock with almost anything small and flat. I used a car key to see if it would open it. A flathead screwdriver would work…. So I don’t think this qualifies by any stretch of the imagination to be called a Lock. So now I’m looking on Amazon for a Cam Lock. However I’m hoping Vevor Customer Service can team me the exact size. I asked under “Questions & Answers” but they responded basically saying to replace the guts of the lock with a key’d part…. That sends like much more with then ordering a whole new Cam Lock…. Anyways. That is my only real complaint. Other than that I love it. It feels really sturdy and seems to be really well made and of high qualify. I didn’t love the price… but you know, You Gotta Pay To Play. I’ll attach some pics. It’s not done. The plug situation is a mess. The Electrify American plug to the wall is beyond short. So I’m going to have to move some things around to make it all hang pretty. Will post updated pics soon.

After looking for a good deal I settled on this Vevor nema box. It has plenty of room to house all of the electrical components required in my latest build.