Recenzje klientów dla VEVOR Przecinarka do płytek, długość cięcia 1200 mm Profesjonalna ręczna przecinarka do płytek, grubość cięcia 6-15 mm Naprowadzanie laserowe Precyzyjna przecinarka do płytek Przecinarka do płytek z metalowym kółkiem tnącym

Generalnie tnie, ale wygina sie jak szalony. Nawet przy krótkich plytkach, zeby uciac równo, wypadałoby odkręcić, bo przy tych 30cm jest na tyle miękko i brak oparcia dla prowadnicy ze ostrze nie ma jak rysować, dopiero od 15cm zaczyna ciąć.

i tried using it on one cut and it cut crooked. i should have read the reviews prior to purchase, i only wish i could leave a zero star review. spend more money and get a better quality tile cutter.

J’ai fait un travail avec cette scie a carreaux et je ne suis pas satisfait , le rail supérieur ou le couteau glisse n’est pas assez rigide , par conséquent , les grands carreaux sont plus problématique.

its not working at all. it does not make a straight cut lost a lot of tiles hope I get my refund. I think this size is no good as the rail get bend when you move to cut.

Para cortar azulejos pequeños supongo que sirve. Los de 120 no los corta bien.

I bought the 47 inch tile cutter about 2 months ago and have done one project with it. I found the laser light useful particularly as the built in square on the tool was not square. The roller cutter was smooth and cut cleanly. There was flex in the base so one had to ensure it was on a solid table. I would not recommend this tile cutter for extended use as it required more measuring because of the out of square guide.

Mécontent du fait que la poignée de la carrelette s'est cassée dès la première utilisation ! Réclamation faite auprès du site mais resté sans réponse depuis plus d'une semaine ! Merci Vevor de votre inefficacité !

sur cette longueur les barres de support du chariot de coupe sont trop souple et se souleve dès que j'appui pour effectuer une coupe donc inutilisable en l'etat et cela m'a couté un carreau en 120*60 ... rien d'autre a ajouter

I bought this to cut large format tiles, 24 x 48. I have several smaller cutters. The trend to larger tile sizes forced me to get a new bigger one. The packaging looks good on the outside. However when I set it up and started using it I quickly realized it was going to be a challenge to get the job done correctly. One of the biggest gripes I have is they didn't calibrate the tool. There maybe a laser mounted on the head but as is out of the box it's useless. You will need to adjust it. Then I put a tile in and scored it, pressing the snap bar separated the two halves. pull it out from the bed and how off square could it be? Try 1/8" per foot. That is ridiculous. The rails seem too thin for the length that they are. The car slides nicely. There are these wings on the sides to support tile overhang. They are flimsy are get in the way if you're not using them. The unit is put together with nylock bolts and screws. Put aside 3 hours to setup and calibrate. It's not ready to use as is out of the box. Would look elsewhere for a more robust accurate tool.

Purchased in September 2026 in preparation for a tile project using 24x48 large format tile. I needed to reduce the length of my tile to 24x32, so laid the long side against the backstop. Since it's a 24-inch cut, you need to start scoring at the middle of the tool. The 2 bars that the cutter slides on will bow when you press down to start scoring 24 inches away from the backstop. You cannot get sufficient pressure against the tile to properly score it at the beginning of the cut, and you will not get a straight edge. Not only did I waste over $100 on this useless tool, but I also now have to purchase a replacement tile. Stay away from this one!