Recenzje klientów dla Zestaw ściągaczy łożysk VEVOR 14-częściowy, 5-tonowy separator łożysk, zestaw do demontażu łożysk kół zębatych ze szczękami 2- i 3-calowymi, zestaw ściągaczy osi piast kół, wytrzymały zestaw narzędzi do rozdzielania łożysk z walizką
Ściągacz łożysk typu Chuck
Opinie klientów
Jak działają recenzje i oceny klientów
Opinie klientów, w tym oceny produktów w formie gwiazdek, pomagają klientom dowiedzieć się więcej o produkcie i podjąć decyzję, czy jest on dla nich odpowiedni.
Nasza ogólna ocena nie jest zwykłą średnią. Priorytetem są dla nas autentyczne, wiarygodne recenzje i odfiltrowujemy duplikaty lub nieaktualne treści przed obliczeniem ostatecznej oceny. Dzięki temu mamy pewność, że ocena rzeczywiście odzwierciedla rzeczywiste doświadczenia klientów.
Oceń ten produkt
Podziel się swoimi przemyśleniami z innymi klientami
Napisz recenzję
106 Recenzje
Recenzje Bieżącego Produktu
Zweryfikowany zakup
Tylko zdjęcia i filmy
Przetłumacz wszystkie recenzje na Polski
Mr
I had to modify the jaw to make it work in my application, and after the second use the threaded rod that holds the jaw snapped.
Not a lot great to say about the product, but customer service was great.
Vevor sent me a full refund after I shared photos of the failed part.
0 osób uznało to za pomocne
Przetłumacz recenzję na Polski
Konsulent
Denne er helt ok.
0 osób uznało to za pomocne
Przetłumacz recenzję na Polski
Mr
Used on smaller scooter engine, pullers a little large for small bearings, but managed to pull bearings from the crankshaft. The set is probably intended for larger engines.
0 osób uznało to za pomocne
Przetłumacz recenzję na Polski
Albarran
Ściągacz łożysk typu Chuck
Producto de calidad regular
0 osób uznało to za pomocne
Przetłumacz recenzję na Polski
Needs work to be a great tool
Bolts bend and one broke off. I have to source some grade 8 bolts from my local hardware store to use on it. Maybe fix the bolt problem and it won't be a bad tool. All this while removing carrier bearings on a 8.8 axle. So no I didn't put to much on it.
0 osób uznało to za pomocne
Przetłumacz recenzję na Polski
Very Cheap
Received bearing puller kit with damaged blow molded case. Very low quality I don’t have high hopes for damage free operation.
0 osób uznało to za pomocne
Przetłumacz recenzję na Polski
Soft Bolts
I bought this item to remove a wheel bearing from the hub.
The kit arrived promptly and appeared solid.
However, was not up to doing the job, bolts which should pull the jaws of the bearing separator plate are too soft and bent like bananas. I had to use other means to remove the bearing.
I am going to buy some high tensile bolts to try next time. But I'm not sure how tough the metal used for the separator plates is.
0 osób uznało to za pomocne
Przetłumacz recenzję na Polski
Użytkownik nie pozostawił żadnych pisemnych komentarzy.
0 osób uznało to za pomocne
Przetłumacz recenzję na Polski
Broke on the first use
The push rod is very soft. The point at the end crushed at my first try to remove the bearing of an angle grinder.
Then the push rod and the holding rods bent too.
0 osób uznało to za pomocne
Przetłumacz recenzję na Polski
Bolzen abgerissen
Ściągacz łożysk typu Chuck
Schon beim ersten Einsatz ist einer der Gewindebolzen abgerissen. Sehr schade. Lieber mehr Geld ausgeben für was Gescheites
2 osób uznało to za pomocne
Przetłumacz recenzję na Polski