Recenzje klientów dla Piła łańcuchowa benzynowa VEVOR 62 cm³, piła łańcuchowa 508 mm, mocna piła 3,6 KM z uchwytem antypoślizgowym, dwoma zbiornikami paliwa i funkcją zatrzymania awaryjnego, maks. 11800 obr./min, do wycinki, przycinania i karczowania drzew

Got it yesterday put it all together but didn’t have fuel or bar oil. Put gas and bar oil in it this morning and the pull cord broke the 6th pull. So can’t even use it till I fix this brand new saw now.

I bought this saw to accompany one I had already purchased which was great in power, throttle responsiveness and performance; however this saw was a disappointment. It did have power and the like but leaked fuel from the bottom seam of the fuel tank. I only realized it once setting it down to watch my gas run everywhere and puddle up. It leaked so much I couldn’t use the saw. Still waiting on a replacement.

Comme je vous ai informé le 22 septembre 2026 sur votre site tronçonneuse ne fonctionnait pas car elle ne démarre puis je demande remboursement de ,71,90 maintenant veuillez m'indiquer ce que veut dire le niveau v1 et comment atteindre le niveau V4 pour être remboursé cordialement

Très déçu, en fait, au début, problème de démarrage et maintenant difficulté de démarrer à chaud en plus lanceur HS

These EU versions are different from the US versions. This is a ultra low-quality, trash chainsaw. Mine came complete with a cracked air filter, compression loss, and a screw that came loose and wreaked havoc on the flywheel, sending dangerous shrapnel flying. DO NOT BUY THIS SAW. Vevor needs to pull this trash off the market. Edit: Turns out that this saw is actually 54cc. The piston measures 45mm (not 45.2mm like many other "62cc" saws) and is based on a much cheaper chassis than the US model. So there's no upgrade path for the top end either. This european model is a massive downgrade from the US model.

Very finicky starter… choke once then pull a bunch. When sitting, it leaks bar oil. Cuts good.

Bought the Vevor 62cc 20” chainsaw a few weeks ago to have a back up, since testimonials were good. Used it two weeks ago on a medium size spruce tree. It cut well but died a few times while cutting for no reason and the started up was hard. I noticed the throttle trigger does not lock at full rpm for starting like other saws I have, is it suppose to, is it broken? Makes it hard to start cold. The pull is also much harder than my other similar sized saws. Okay for the money as long as it holds up for a while.

Got 3 trees down, it’s shot. It worked long enough for me to get done what I wanted. Save some money and buy a better saw. Can’t get replacement parts.

At first, I was impressed...until I got around to using it. First off, installing the bar to the saw...meh. Took a minute. Very cheezy set up. Felt like I was going to break the chain tensioner to get the chain tightened to my personal preference...just slack enough to read 2 pitch numbers pulling from the top of the bar. Second, the retaining nuts for the bar wont tighten enough no matter how much you tighten them again afraid I was going to break the studs off...because it feels cheap. Oh and one nut falls off while operating...no matter what! Using thin washers behind the nuts seemed to do the trick however. Not a fan of the "Ez start" You can't hold it with 1 hand and start it with the other! Impossible! LAME!!! Have to use your damn foot on the ground or squeeze it between your knees! No primer bulb no carb adjustments. Takes 5-8 pulls to start even when hot! BUY EXTRA CHAINS WITH YOUR ORDER! They dull quick but do sharpen well. I run Amsoil 100:1, non ethanol 91 or race gas 40/60 in all my 2 strokes. Dirt bikes, sleds, weed eaters and several chainsaws. I also rebuild all my motors and trust the 100:1 mixture 100%. I run 50: 1 and do a religious heat cycle break in procedure for the first 10 hours before I switch to 100:1. This saw was real boggy on the bottom end @ 50:1 for about 5 tanks then leveled out and seem to come around after about 3.5 hours of use. When I switched to 100:1...the saw came alive! WOW!!! It runs soooo good! Very powerful, very clean running, no bogging...but still takes 5-8 pulls to start! Lmfao! Have approx. 60 hours on the saw cutting only railroad ties for a huge retaining wall and 12 large railroad tie garden boxes. What I bought the saw for. The bar has held up flipped every 5 tanks but went through a dozen chains...I've gotten my money's worth 10 fold for sure!

Saw runs good and has plenty of power, but it leaks ALOT of bar oil EVERYWHERE!