Recenzje klientów dla Piła łańcuchowa benzynowa VEVOR 62 cm³, piła łańcuchowa 508 mm, mocna piła 3,6 KM z uchwytem antypoślizgowym, dwoma zbiornikami paliwa i funkcją zatrzymania awaryjnego, maks. 11800 obr./min, do wycinki, przycinania i karczowania drzew

La motosierra se atasca con ramas finas y desmonta la cadena, o bloquea su giro de cadena.. Mala motosierra, mala compra, tengo otra motosierra de otra marca y con esa, tendré que hacer el trabajo.

Thank you for good service so far. For preparing the saw before use, some screws had to be tighten properly. After that the mounting went good. I have tried the saw, and have some comments. Easy to start, but it’s recommended to put som chain oil on the chain before starting. When sawing, the chain became too slack and needed to be tighten up. This happened tree times on a job that took around half an hour. The screws for attaching the chain sword were properly tightened each time. This I consider as a safety risk if the chain goes off when sawing. I am not sure how to fix this. In general, the saw were cutting fine, but I have not used it long enough for a proper judgment yet. BR.

Fait son travail un peu lourde

Desearía saber si a mi motosierra se le puede acoplar un espadín ( guía de cadena ) más pequeño, en vez de 55 cm , puede ser uno de 35- 45 cm. ?

Tiene muy buena pinta , wsta a prueba a ver como sale y si decir que el envio tardo mucho. Gracias

the chain was of poor quality - replaced it with an oregon chain - working fine now.

Les plastiques semblent très fragiles. La vis noire qui meintient le petit cache filtre à air ne tient pas et peut être facilement perdu. La griffe à dent est fabriquée dans un metal trop tendre et a plié tout de suite et je n'ai pas trouvé un modèle plus solide pour ke remplacer. La consommation en essence est très grande. La lame de chaîne n'est pas assez rigide, ce qui peut causer que la chaîne saute.

I have been blessed by the best in my life and oh the stories I could tell. I didn't really buy thiis chainsaw it was more of an Excalibur moment. As I was walking towards the outskirts of Quincy, California...there it was. The 62 cc's lodged in a large Doug Fir and a line of people trying to get it unstuck. First a froggy young man walked up with confidence and grabbed the handle. He yanked and twisted but it he could not pull hard enough to release the black and orange pearl of a chainsaw. Next up was a wise priest who prayed over the pinched bar to no avail. I felt a tap on my shoulder and as I turned to see who needed my attention....a young tip toed lass whispered into my ear...."I is yours, it is yours, it is yours." When I turned back looking over my shoulder there was no young lady to be seen. In a moment I felt it might be me to turn the tide. I walked unsteadily through the crowd and I layed my hands on the handle, I pulled the cord once and it popped, the second pull caused full ignition and I pulled gently on the handle and saw released itself to its master. I turned still grasping saw freed to do the lord's work. The trigger pulling louder with each iteration of my trigger finger. All 62cc's barking in unison and with my smile a shedded tear. I have found the right price, the right size, and the right quality., and the right chainsaw for cutting firewood on my acre lot. I hope you have a similar experience.

I purchased the Vevor small top handle saw first and then I bought one of the Vevor pole saws. Then I moved up to this bad boy here. I've owned and still own quite a few saw. Stihl, Husqvarna and Echo saws have been my go to saws for years but, my big Husqvarna was in the shop and I thought what the heck, I can buy an inexpensive Vevor 62cc saw for $100 or so and use it until my Husqvarna gets fixed. The problem is that on the second pull the top part of the pull rope guide just snapped off and went flying. Yes, the pull rope guide is made from plastic where every other saw on the market uses a metal pull rope guide. So if you try to start this saw make sure that you are pulling straight up only. Also, pull the the rope gently until the engine is rotated until the pull rope handle has tension on it and it as close to the saw as possible. It doesn't have a compression release and getting the engine turned exactly right will help with getting it started. You'll understand after a little use of the saw. The next problem with the saw is that mine cuts to the left severely. I can't tell that the bar is bent or that anything is damaged. Typically, when this happens on a saw with a long bar it's because the teeth on one side of the chain were not sharpened on the same angle as the other side of the chain. Since this was on a new saw with a new bar and new chain, i can't really say what is causing it to cut to the left. I'm 57 and work for my local electric company and have over 35 years of experience cutting down trees and limbs so I'm not inexperienced. The saw does have plenty of power but, I think the clutch is a little weak and engages too soon sometimes when the saw is cutting into some hard wood. The chain will stop turning but, the engine is still revving pretty high. So the amount of power is impressive but, the clutch won't allow you to load the engine up very hard before the chain stops spinning. You just have to adjust your amount of pressure on the saw as you cut to not let it happen. The saw does sound fairly loud and aggressive and it has plenty of pep. I would highly recommend ear muffs or plugs. Oh yeah, one of the biggest issues with this saw is the lack of a primer bulb. I've never had an issue with any of my other saw getting restarted after running the tank empty. This 62cc Vevor saw is very difficult to get restarted if you let it run out of gas. Normally, on my other saw if I kill the engine the second that I hear it running out of gas I can refill the tank and get the saw restarted within 2 or 3 pulls. This Vevor is going to wear you out cranking it to get it restarted after running out of gas. It's a pretty thirsty saw when cutting through some hard wood so it's going to empty the tank pretty fast. You would probably be better off squirting some gas directly into the carburetor a few times to help get it restarted quicker instead of wearing yourself out pulling the rope 20 times.

Pull ripe and recoil spring broke on first use. Bar not heavy duty. Waiting for replacement under extended warranty.