Recenzje klientów dla VEVOR Wiertarka Magnetyczna, średnica Wytaczania 1100W 1,57", Przenośna Elektryczna Wiertarka Magnetyczna 2697lbf/12000n Z, Wiertarka O Maksymalnej Prędkości 580 Obr./min Do Dowolnej Powierzchni

I have drilled probably 50,000 holes in my life in the construction industry with a mag drill costing 10 times the price. Vevor makes tools available at a great price to value ratio. So many bits and they seem to cut good. Oil bottle is often in the way when trying to drill holes. It could be secured much better than the current setup. The whole reason for a mag drill is drilling upside down etc. The magnet even on a flat clean surface is not powerful enough in my opinion. On my bench in my garage I hard trouble pulling soft enough on the handle to start the 1/2” hole without the drill skipping sideways across the metal. Once the hole got started it was ok. I tried drilling a hole on the side of my galvanized trailer and the magnet wasn’t strong enough to hold it there even with the drill in the off position. I think this product was rushed to production to quickly. So many areas for improvement.

A única coisa que me incomoda nesta máquina é a temperatura elevada que registei nos 60° mesmo quando não estou a trabalhar com ela pois basta estar ligada a parte electromagnética e ela aquece bastante na minha opinião. Já referi este inconveniente à vevor ainda não recebi uma resposta conclusiva.

The screws get lose easily. Overall quite ok. Made my welding table with this machine.

Nu este ca în descriere când dai gaură magnetul se dezlipește nu are suficientă putere

får ikke justert bor hastigheten med denne.

Inte alls imponerad, magneten känns väldigt svag och håller inte alls emot när man skall borra. En miss va även att man inte valde en med variabel hastighet då den går för fort.

Ce modèle ni dispose pas de variateur de vitesse. Est il possible d'échanger?

I have had this drill for about one year and have used it 3 times. The last time I used it I noticed a Crack in the body of the drill head. Upon further inspection, I noticed the only thing holding it together was the clamping bolt. When I removed the bolt the casting fell apart. At that time I could see the porosity in the casting that was evident in the machined surfaces and through the coating. This is a defective part and should have been caught in the manufacturing process. This is clearly an inferior product. I'm just thankful I discoved the issue before it caused an injury.

Die Maschine machte auf den ersten Blick einen soliden Eindruck. Leider war bei dem Bohrfutter eine große Beschädigung, man versprach mir ein neues zu schicken. Aber nach ca. 10 gebohrten Löchern kam Rauch aus der Maschine und es roch verbrannt. Mal schauen was Vevor sagt?

első használatba vételkor már elkezdett "síkítós hangon" recsegni ropogni(valószínű darálja a fogaskerekeket), a mágnes ami elméletben 2000 n (kb. : 203,944 kg) erővel húzza magát a vashoz levált szinte azonnal mikor a vashoz ért a 10-es fúrószár, mindezt úgy hogy előtolása mérve is alig pár(max 5-10 kg) kg volt. egy romhalmaz az egész. még nem adta fel a harcot, de biztos az lenne a vége ha folytatnám a használatát. A megvételét ssenkinek nem ajánlom. When first used, it started to crackle with a "squeaking sound" (it's probably grinding the gears), the magnet, which in theory pulls itself to the iron with a force of 2000 N (approx.: 203.944 kg), came off almost immediately when the 10-mm drill bit touched the iron, all this while its feed was barely a couple (max 5-10 kg) kg. The whole thing is a pile of rubble. It hasn't given up the fight yet, but that would definitely be the end of it if I continued using it. I don't recommend buying it to anyone.